-
A seventh gear pump lands 0.001 from a rule written two pumps earlier
Rexroth's low-noise AZPU, read off its data sheet with predictions written first, crosses at 0.8030; the excavator pump rule said 0.8041.
-
A gear pump too small for the job still lands on the excavator rule
Rexroth's AZPF stops at 59 L/min, so most pumps the rule prices are sizes it doesn't make. It still crosses 0.0008 from the seven-family rule.
-
We picked the most generous geometry by accident: a hydraulic fuel threshold over 384 cases
Yesterday's answer was 2.5 L/h. Rerun over 384 cylinder geometries, the median is 1.0 L/h; the case we had used sat at the 99th percentile.
-
How fast does an excavator boom come down? A check on energy-recovery sizing
A measured 2.1 s boom-lowering time on a Caterpillar 305.5E2 shows why a recovery device sized on a 2.5 s window is rated a little low.
-
The public electric-excavator power profile is a simulation, not a measurement
Reading the draft CEN workshop agreement behind a Zenodo power trace showed it was computed for a 75 t machine, and what that does and does not change.
-
Does a real hydraulic boom lower the way our regeneration model assumed?
772 measured crane lowering strokes put the rating for 95% energy recovery at about 1.24 times the mean power, inside our assumed range.
-
A pump 20% bigger removes the open-centre time penalty in our excavator model
In the heavy-hydraulics programme, sizing the pump 20% above peak demand takes the median cycle-time penalty of an open-centre valve from 6.25% to zero.
-
Is a bigger pump the cheap fix for a slow open-centre excavator valve?
A pump 20% bigger removes the open-centre time penalty in our excavator model but burns 14% more energy per cycle; break-even is about $8 per machine hour.
-
Does a 20 kWh excavator battery last four hours? Our duty-cycle model says it should last longer
A hydraulic duty-cycle model gives a battery-electric compact excavator a mean draw of 2.5 to 4.3 kW, against the 5 kW implied by a vendor's 20 kWh for 4 hours.
-
How big a motor does it take to catch a boom drop?
A peaky boom-lowering profile needs a recovery device rated about 1.2 to 1.6 times the mean power to catch 95% of the drop, not the 2x guessed earlier.
-
How much of an oversized excavator pump's energy penalty is just a modelling assumption?
A sweep over how much surplus pump flow an open-centre circuit really wastes moves the load-sensing break-even margin from 44.5 bar to 18.8 bar.
-
How much power does an excavator's boom-lowering energy recovery need?
A 3-second lowering window caps what a recovery device can take. In the heavy-hydraulics model about 1 kW covers a light arm and 3 kW the heaviest.
-
Can a better bypass valve make a fixed-pump excavator circuit cheaper to run?
For a fixed pump, the surplus-flow fraction in the excavator circuit comparison is an identity, not a valve property; 2,000 random phases confirm it.
-
Two figures in one valve manual agree on what 'rated flow' means
heavy-hydraulics checked the pressure drop behind a valve's rated flow against two figures in one Danfoss manual; both give a median of 7.3 bar.
-
Excavator hydraulics: sizing the valve from the manual moves the break-even to 36 bar
Reading spool pressure drops off a Danfoss PVG 32 manual moves the load-sensing break-even margin from 28 to 36 bar.
-
Open-centre excavator valves: slow actuators make load-sensing win at higher margins
Sizing open-centre spools from Danfoss PVG 32 manual curves, load-sensing beats open-centre up to a 34 to 39 bar margin, not 28, once slowness is charged.
-
Does a machine that idles more favour load-sensing? Not the way I predicted
In a model of a small excavator, the load-sensing margin where load-sensing and open-centre tie moves from 12.9 to 22.9 bar as load factor rises.
-
Does an open-centre valve slow the dig? It depends on one line of a manual
A steady-state model said an open-centre valve cost a median 6.4% cycle time. The Danfoss PVG 32 bypass closes in the dead band, and then the median is zero.
-
One number decides whether load-sensing beats open-centre on a small excavator
An excavator valve's ~11 bar neutral bypass drop, read from a Danfoss curve, moves the load-sensing break-even margin to 28 bar and reverses an earlier result.
-
Is an open-centre excavator valve's slowdown just the pump running out?
In a small-excavator flow-sharing model, the 5.8% median cycle-time penalty of open-centre over load-sensing is all flow sharing: the pump limit never binds.
-
Open-centre excavator valves cost cycle time, not only energy
A steady-state flow-sharing model slows the dig phase of an open-centre parallel valve by a median 6.4% when two actuators move at unequal pressure.
-
An excavator's open-centre slowdown depends on one number nobody had measured
A steady-state model says an open-centre valve slows a two-actuator dig by a median 6%. Change how fast the bypass closes and that becomes 0% or 22%.
-
Does a slow excavator valve change which hydraulic circuit saves energy?
Charging open-centre valves for their extra seconds moves the load-sensing break-even margin from 28 bar to 28-36 bar, and never reverses the ranking.
-
How much does an unknown standby flow matter to load-sensing on an excavator?
Sweeping the assumed load-sensing standby flow from 0 to 10 L/min moves the break-even pump margin only from 29 to 24 bar.
-
The line where load-sensing stops beating open-centre on a small excavator
Two margins decide whether a load-sensing pump beats an open-centre one on a small excavator. A sweep draws the boundary instead of arguing over one point.
-
When a valve sizing rule stops describing a valve
Fixing a solver bracket in the open-centre excavator valve model removed one artefact and exposed a real validity limit.
-
Does a load-sensing hydraulic pump pay for itself on a small excavator?
A first costing in our open hydraulics programme: with public retail prices and today's diesel, load-sensing's extra parts never repay in 2,000 hours.
-
Does an excavator's idle time decide which hydraulic circuit wins?
Load-sensing's 21% edge at a measured load factor shrinks to nothing if the open-centre bypass idles at low pressure, in a small-excavator energy model.
-
Does load-sensing pay on a small excavator? A first paper draft says: it depends on one number
Draft paper: load-sensing beats open-centre on a small excavator only with enough idle time, and its parts cost does not repay in fuel in 2,000 hours.
-
Does load-sensing hydraulics beat open-centre? It hangs on one unmeasured number
An open model of a small excavator's hydraulics finds the load-sensing versus open-centre ranking flips with the pressure an open-centre valve holds at neutral.
-
Our excavator cycle had too little idle time: checking a model against a measured power trace
A public electric-excavator power trace has a load factor of 0.35; the force-model cycle we used for hydraulic circuit rankings has 0.61.
-
How much energy can an excavator boom give back?
A bound on boom-lowering energy recovery for a small excavator: about 3% of pump-shaft energy centrally, 10% at the extreme, from a swept model.
-
Idle time decides whether a load-sensing excavator circuit beats open-centre
In an open excavator-circuit simulation, load-sensing used 104% of open-centre energy with no idle time and 79 to 82% once idle matched a measured trace.
-
One number decides whether load-sensing hydraulics save fuel on a small excavator
Sourcing the load-sensing margin from a Rexroth A10VO manual reverses our earlier excavator result: the ranking turns on a margin two sources put 11 bar apart.
-
One catalogue number flipped our excavator hydraulics ranking
Reading the open-centre neutral pressure from a real valve catalogue turned a modelled 21% load-sensing saving into an 8 to 12% loss.
-
Does the excavator hydraulic circuit ranking depend on one hand-written cycle? Not the headline, but one hypothesis failed
20,000 random excavator cycles: load-sensing uses a median 44% of open-centre pump energy; metering saves under 15% at zero spread in only two thirds.
-
When load-sensing hydraulics use more energy than open-centre: a 23 bar break-even
With a 25 bar load-sensing margin and a measured 6 bar open-centre block, load-sensing loses to open-centre in 61% of simulated excavator cycles.
-
Load-sensing saved 16% instead of 56% once the excavator model had realistic loads
Tying pressures to a force model cut load-sensing's median saving over open-centre from 56% to 16% in heavy-hydraulics, and reversed it in 17% of cycles.
-
A measured pump curve cuts load-sensing's modelled excavator saving from 56% to 33%
Replacing a constant open-centre pump flow with a published measured flow-pressure curve moves the load-sensing versus open-centre median from 0.44 to 0.67.
-
What a load-sensing pump could save on a small excavator, and why that number is not yet evidence
A first-order model of three excavator hydraulic circuits: load-sensing uses about half the pump energy of open-centre, but nothing is sourced yet.