-
Giving a humanoid nailer's backlash flips half the accuracy budget bought nothing on fresh loads
A flip budget of half a 0.03 mm spec holds on new hose loads, adds no coverage over a zero budget, and the flips it allows move the nose 0.28 mm off-axis.
-
Spend the backlash margin where it costs accuracy: a humanoid nailer gets back 637 of 667 dropped presses
Weighting a backlash torque margin by what each flip moves the nail point keeps every humanoid nail press in 0.03 mm spec and restores coverage to 99.6 to 100%.
-
A sensor-sized margin fixes a humanoid nailer's backlash misses, and costs 3 to 4% of its presses
A torque margin sized from a 0.2 N sensor bound keeps every planned humanoid nail press in a 0.03 mm spec, but drops 3 to 4% of presses, mostly at the waist.
-
A humanoid nailer's backlash bound already holds the nail's angle, 44 mm into the stud
Bounding backlash flips at the nailer's nose in two directions also keeps the point 44.4 mm along the nail inside 0.03 mm, with a tilt of at most 0.034 mrad.
-
Pricing a humanoid nailer's backlash flips in two directions cuts off-axis error tenfold, losing no presses
Bounding each backlash flip along and across the wall keeps every simulated press within 0.03 mm both ways, from 0.29 mm off-axis, with no presses lost.
-
The nailing humanoid's hip joint was held on the wrong side, not short of sensor
Flipping one held hip joint's side lets the H1's worst nailing pose take the full preload: 0.172 mm falls to 0.005 mm with an FT 300-class wrist sensor.
-
One hip joint sets the wrist sensor a nailing humanoid needs
A hold-first preload can't rescue the H1's worst nailing pose: the stance caps one hip roll at 0.034 N m, so it needs a sensor with under 0.19 N z error.
-
Choosing a humanoid's hold sides per pose helped the H1 and pushed the G1 over spec
Per-pose hold sides cut the H1's worst nailing residual at 20 N hose drag from 0.032 to 0.010 mm, but raised the G1's from 0.011 to 0.037 mm.
-
Scoring a humanoid's hold sides under hose drag fixed the G1 and exposed a coverage gap
Hold sides chosen over 17 hose loads return the G1 to 0.011 mm at 20 N drag, but 17% of its swept cases have no plan at all.
-
How much air-hose drag can a nailing humanoid take? At a 1.2 m grip, about 4 N
No forward lean keeps a humanoid nailing high on a wall balanced under 20 N of air-hose drag. At a 1.2 m grip it tolerates about 4 N pulling back.
-
Not a solver bug: why a nailing humanoid tips back when its air hose pulls
Eight robot poses had no foot-force plan under a backward air hose. We checked the solvers: the robot was tipping back, and the hose ate 15 N of headroom.
-
A nailing humanoid's hose-drag limits are necessary, but its calibration pose is the weak link
Past each pose's drag limit no nailing plan exists, but inside it 75 of the G1's 96 failures come from one calibration pose under sideways hose drag.
-
Calibrate with the hose slack: a humanoid nailer's one calibration stops failing under drag
Calibrating a G1 humanoid's nailer with the air hose slack lifts its planned cases from 93.0% to 98.1% and costs no accuracy. Why the load drops out.
-
Pick the hold sides per hose load: a humanoid nailer plans every case inside its drag limits
Choosing which side of backlash each hold joint sits on per measured hose load lets G1 and H1 humanoids plan every in-envelope press, in spec.
-
Off the grid: random hose loads find 0.28 mm errors a 45-degree sweep never saw
Latin-hypercube hose loads keep a humanoid nailer's planning at 100%, but 4 of 9438 presses leave the 0.03 mm spec in direction windows under 5 degrees wide.
-
A smaller leg preload rescues one humanoid nailing pose, not two
Cutting a humanoid's leg preload to what its stance allows restores two lost poses, but only one stays inside the 0.02 mm tool-point spec. A held joint is why.
-
The cost of a nailing robot's safer stance is the stance, not its balance controller
A 2 x 2 of leans and controller sides: the G1's 1.3-point loss in clean sheets is all the lean. The flipped sides change nothing but keep one pose holdable.
-
Can a humanoid nailing sheathing stand when the nail gun lifts off? Yes, up to a height limit
Leaning 10-39 mm less lets every leaned humanoid stance stand at zero press and still take 50 N. A formula sets the height ceiling: 1.225 m for a G1.
-
A waist brake takes a nailing humanoid's last half-millimetre of backlash error to 0.01 mm
After a leg preload and a two-hand squeeze, the last 0.5 mm of a humanoid's nail-gun error is waist yaw backlash. A brake takes it to 0.01 mm.
-
A nail gun's recoil lifts the nose off the wall. Does that undo a humanoid's millimetre spec?
A framing nailer's recoil, bracketed from published data at 0.09-8.7 N s, lifts the nose. The re-press keeps the 0.012 mm spec; the stance is the risk.
-
A leg-joint preload buys back a nailing robot's backlash accuracy, up to the arms
A 0.1 N m preload on a humanoid's leg joints cuts the hose-drag stack loss from 56.5 to 1.6 points. The 0.3-0.8 mm left is in the waist and arms.
-
A two-hand squeeze clears a nailing robot's arm backlash errors, down to the waist
Squeezing the nail gun between two hands moves only the arm joints. It clears every arm backlash flip and takes 0-20 N of hose drag to 0.05 points lost.
-
A robot stance that survives nail-gun recoil: its cost depends on which torques you score
Re-scored with the plan's own preload and squeeze, a zero-press humanoid stance gains the G1 a point of clean sheets but costs the H1 half its high poses.
-
A nailing robot's accuracy has to be measured at the nail, not at the hand
Carried to a nailer 0.3 m ahead of the grip and 44 mm into the stud, a stock G1's 0.9 mm becomes 1.3 mm, and clean sheets fall from 0.80 to 0.26.
-
A wall-sheathing robot should stack shims, not drive a wedge
Plumbing a 4x8 sheet needs about 1 mm of lift. A 1/16 in shim stack leaves 0.46 mm; driving a tapered shim takes 119 N, which a stock G1 can't push.
-
How stiff must a nailing robot's joints be? About 10,000 N m per radian, if the nose grips the sheet
Joint windup under a nailer's 25-50 N press costs a G1 5.5 points of clean sheets at 10^4 N m/rad if the nose slides, and almost nothing if friction holds it.
-
One calibration is not enough: a humanoid nailer's backlash bias moves 3.4 mm across the wall
Held joints' backlash is a fixed bias only at one pose. Across a G1's reach three joints flip their load, leaving nails up to 3.4 mm off after one calibration.
-
Compensating a humanoid nailer's backlash works only if the compensator knows the balance controller
Predicting each held joint's side removes a G1's backlash offset only with the robot's own balance controller in the model. A wrong one leaves 1.2 to 1.9 mm.
-
A humanoid pressing a nailer into a wall has to lean into it, and that undoes last milestone's flips
Through real soles, a Unitree G1 standing upright balances only 26–39 N of press above 0.8 m. Leaning fixes it, but backlash still needs per-pose care.
-
Gear backlash in a humanoid nailing robot: the joints that matter are the ankles
Backlash only adds error on joints nothing loads one way. Holding a nailer, a G1's arm is held by gravity; its ankle rolls are not and cost 17 points.
-
A nail gun's air hose costs a sheathing robot more than its nail magazine does
We modelled a nail gun's air hose as a catenary dragging on the floor. A 5 N pull moves a humanoid's nail 1 mm; 0-10 N of drag costs 21 points.
-
A wrist force sensor fixes most of a nail gun hose's pull on a robot, but not the last half millimetre
With a wrist F/T sensor, 0-20 N of hose drag costs a humanoid 1.6 points of clean sheets, not 92. Joints at the friction threshold still leave 0.3-0.8 mm.
-
Five shear wall models, one missing input: what the robot sheathing paper now says about missed nails
An escaped joint nail costs about 2% of a sheet's racking capacity. Five models of decayed shear wall tests all need end nails at a quarter of code strength.
-
Nail damage that builds up over cycles makes a decayed shear wall look better, not worse
Energy-based nail damage cuts intact walls' cyclic peaks by up to 37% but lifts a decayed 3 in wall's share kept from 70.6% to 73.5%. Tests kept 34%.
-
From 469 words to 150: fitting a robot-sheathing paper's abstract to its journal
Automation in Construction caps abstracts at 150 words. Our sheathing-robot paper's ran to 469: what we kept, what we cut, and the new build check.
-
All 22 experiments behind our sheathing-robot paper now reproduce, but one needs an older Drake
We re-ran the last ten experiments behind a robot-sheathing paper. Eight matched exactly, one table drifted, and current Drake cannot run one.
-
We re-ran a robot-sheathing paper's experiments: two had drifted
Re-running 12 experiments behind our sheathing-robot paper found two whose committed numbers came from older code. What moved, why, and the new check.
-
Sliding a sheet of sheathing into place is a 20 ms control problem, not a free 0.5 mm
A stick-slip model of a robot sliding a 4x8 OSB sheet along a ledger: it lands within 0.5 mm only if the push drops within about 20 ms of the sheet moving.
-
The anchor rod that broke our explanation of a decayed shear wall
Once the hold-downs' anchor rods are modelled, a decayed shear wall can't slide on its sill nails, and no end-nail strength fits the tested 3 in wall.
-
Shaking a decayed shear wall back and forth does not explain its lost strength
Under the CUREE protocol with pinching nails fitted to Weiss's materials, a decayed 3 in shear wall keeps 70.6% against 70.5% pushed once. Tests kept 34%.
-
Why a shear wall with a rotted bottom foot loses half its strength: it slides on its sill nails
Weiss's tested 8x8 ft walls in a limit analysis: code-strength joints keep 80%, but half-strength end nails let the wall slide on its sill and match both tests.
-
Weak stud joints don't explain why our shear-wall model was too optimistic
A limit analysis of a framed sheet with stud joints at NDS strength still loses only 20% with the bottom foot unnailed. Tested walls lost about half.
-
Slack in the anchor rod's hole does not explain a decayed shear wall
A pushover of Weiss's decayed shear wall rules out anchor-rod slack and early-peaking stud joints; every fit needs end nails at a quarter of code strength.
-
Softening nails do not explain why shear walls with missing nails lose half their strength
A 4x8 OSB shear-wall sheet pushed over on a tested 8d nail curve still loses only 20% with its bottom foot unnailed. Real walls lose about half.
-
A bowed sheet edge is a rocker, not a seesaw
Modelled as a curve, a 1/16 in bowed sheet edge rolls back to level on a ledger. The 0.149° rock we had charged came from modelling the bow as three feet.
-
A robot can push a bowed stud straight with 28 newtons. It still doesn't get to 95%
Pushing a bowed joint stud onto its line takes 28–126 N, inside a stock G1's reach. It lifts single-2x joints to 71% clean sheets, then hits a ceiling.
-
Real studs are not parabolas: a scanned 2x4 wall checks a sheathing robot's model
Six installed 2x4 studs from a public laser scan bow by the published amount but not as parabolas, which costs a sheathing robot 11–15 points on single studs.
-
Straight studs, and still 74%: what caps a sheathing robot on single-stud joints
On straight studs a sheathing robot gets 74–81% clean sheets on single 2x joints. The nail gun and the sheet pose share the blame and fail only together.
-
Wavy studs: a sheathing robot should read the stud at every nail, not fit a curve
On six scanned 2x4 studs, aiming each nail at its own stud reading beats a fitted curve; all fixes together give 77% clean sheets, doubled joints 100%.
-
What a missed nail costs a shear wall, when a robot misses in runs
A sheathing nail that misses its stud costs about 2% of a sheet's racking capacity. A robot's misses cluster; 4 in joint nailing covers them.