-
A 37 inch wall with a 32 inch door in it
A real Revit house exports door jambs as short walls; a new ifc-engine flag drops them, clearing one of three 2nd floor refusals.
-
When a command-line tool says no, say it in JSON too
The open-source wall framing takeoff CLI now prints a parseable JSON refusal on stdout when you ask for --json and a report cannot run.
-
Counting the frieze board under the soffit
The wall-framing takeoff now counts the frieze board under the soffit, the trim that runs along the wall beneath the overhang, as a new option.
-
Fuzzing the gravel and mulch estimator
A seeded 400-case property test for the wall-framing project's bulk material engine found no defect and now pins its volume, weight, bag and cost arithmetic.
-
Fuzzing the fence takeoff: 400 random fences, seven invariants
The fence module had four hand-counted tests. A 400-seed property test now checks that its posts, bays, pickets and concrete add up.
-
Fuzzing the stucco takeoff found nothing, and that is a result
300 random wall runs through the stucco takeoff: stock always covers the area, waste never shrinks an order, and hostile settings are refused with a reason.
-
A retaining wall with a geogrid layer every 1e-9 courses
Probing a day-old retaining wall calculator by hand found that a fractional geogrid spacing produced absurd material counts. It now refuses with a reason.
-
Half a bedroom: a ventilation input check
The ventilation field on the insulation page accepted 2.5 bedrooms and gave a ventilation rate for a house that cannot exist. Now it wants a whole number.
-
A header size checker that ships no code values, on purpose
Paste the header span table from your code or engineer, list your openings, and see which header each needs and which hand-picked ones fall short.
-
How many pavers and how much base gravel does a patio need? A free calculator
A free paver patio takeoff: pavers with waste, compacted base tons, bedding sand, edge restraint and joint sand, with planters subtracted.
-
How many posts, rails and pickets does 100 feet of fence take? A free calculator
A free fence takeoff that cuts each run into equal bays so rails end on posts, and counts posts, pickets, concrete bags and fasteners.
-
How many retaining wall blocks, caps and gravel does a wall need? A free calculator
A free segmental retaining wall takeoff: blocks with the buried course and waste, caps, compacted base, drainage stone, fabric, pipe and geogrid.
-
How much waste does a framing allowance need to be right? Often none
Two common stud-count rules of thumb, tested against a counted, optimised lumber order on three houses: the waste each would need to break even.
-
Is a 4x8 sheet long enough for an 8 ft wall? No, and here is what to buy
An 8 ft stud wall is 97-1/8 in tall once its plates are on, so a 4x8 sheet is short. A free browser calculator counts the sheets and picks the cheapest length.
-
One null in a shared check: a small bug in a construction takeoff tool
A 13-line helper used by a dozen settings validators in our wall-framing takeoff tool crashed on a missing value. Found by fuzzing, fixed in one line.
-
The last unfuzzed quantity engine in the framing takeoff now has a fuzz test
The paver patio engine was the only quantity engine in wall-framing-takeoff without a seeded fuzz test. 400 random jobs found no defect.
-
Pinning the one link that takes money: a test for the bid-package checkout
The wall-framing bid package has one public checkout link and no test on it. A test now fails on plain http, credentials or a secret in the link.
-
Real wall heights make a real house stop framing
Reading each wall's and door's height from a Revit model, instead of defaults, shows where the Schultz Residence's doors do not fit under its plates.
-
Two small IFC rules move a real house's upper floors closer to framing
A 1.7 in sliver void and a void at a free wall end stopped the framing takeoff on a real Revit house; two IFC reader rules clear three of six refusals.
-
A real Revit house, one floor further: the Schultz 2nd Floor frames
Two drawing quirks in a real wood-frame IFC, tees 1/8 in apart and a door 1.4 in from a wall end, stopped the framing tool. Now the 2nd Floor frames.
-
One 16-foot opening kept a real house from framing
A real Revit wood-frame house stopped the wall-framing takeoff on one 245 in wall with a 189 in opening; a new --add-board flag lets it frame.
-
The sheathing page promised to refuse openings that did not fit, and did not
Probing the day-old sheathing page found 80 openings accepted on 8 ft walls, text sides coerced and nonsense sheet lengths passed. Fixed and pinned by tests.
-
Where to saw a slab: control-joint layout for a concrete pour
A small open-source function lays out control joints for a slab on grade: spacing, panel count, saw-cut feet and cut depth.
-
A free soffit and fascia calculator that shows its packing
Type a house size and overhangs; get soffit panels, fascia boards and J-channel packed into stock lengths with waste. Runs in your browser.
-
Does your spiral stair pass code? A free check in the browser
Type a spiral stair's rise, diameter, pole and treads per turn; see which model-code rule it fails and the most treads per turn that pass.
-
Stepped walls on the framing takeoff page
The wall table now has a Steps column, so a wall whose studs change height part-way along gets its own stud lengths, end studs and plates in the browser.
-
How many bags of stucco does a house need? A free calculator
A free page turns a house size, openings and coat thickness into lath sheets, plaster bags with rebound, barrier rolls and metal trim.
-
Probing a day-old stucco takeoff found a box count of null
Hostile-value probing of the stucco takeoff found six ways to get a raw error or a nonsense count; each is now refused with a reason.
-
The duplicate windows in a real house plan were not duplicates
A framing takeoff refused a real Revit house over apparent duplicate windows; the cause was an unfilled cut behind them, now dropped.
-
Ventilation load on the insulation page
The insulation page now adds the ASHRAE 62.2 whole-house ventilation load to wall heat loss from floor area, bedrooms and heat recovery.
-
How many diagonal braces does a house need? A free calculator
A free page counts diagonal wall braces from your wall lengths, height, spacing and angle, and gives each brace's length and the feet to buy.
-
400 random brace jobs, and the engine held
A seeded property test throws 400 random and hostile wall brace jobs at the diagonal-brace counter and recounts each by hand. No bug turned up.
-
The paver patio takeoff now runs from the command line
wall-framing-takeoff gains a --paver flag: pavers, dig, base, sand, fabric, edge restraint and joint sand from a plan file.
-
When a wall has no studs to splice the plates on
A wall framing engine that could not splice long top plates over studs now also tries joints over a header, with a note, tested on a hand-built wall.
-
A French door under an awning no longer reads the awning's sill
The wall-framing takeoff now tells stacked IFC openings apart by width and lowest sill, fixing a door framed with a 39 in sill.
-
How long should a prefab wall panel be? A free calculator
A new free page splits one framed wall into shop panels no longer than your limit, cutting only where no stud or header crosses, and prints each panel's weight.
-
Advanced framing saves about a quarter of the lumber on a third house, and our table had drifted
Advanced framing cuts the lumber order 26 to 28% on three house layouts, measured with the open-source wall framing takeoff.
-
A bench that quietly stopped running: the allowance comparison
A framing benchmark matched an error message that had since been reworded, so one of its three houses silently dropped out. Found, fixed and pinned with a test.
-
A free bid price sensitivity calculator: what a lumber or labor swing does to your bid
A browser page that restacks your own bid when one section's price moves, and shows how far each can rise before a fixed bid loses its profit.
-
Nailing the blocking: a gap in a framing nail count
The open-source wall framing takeoff placed blocking and fire blocking but never counted its nails. It now does, at a typed count per end.
-
Counting the nails in diagonal wall braces
The open-source wall framing takeoff can now add the nails driven through each diagonal wall brace to its framing nail total.
-
Paint and fireblocking now reach the bid budget
The open-source framing takeoff budget now includes paint and fireblocking lines, priced from typed prices.
-
How many blocks, how much grout: a free concrete block wall calculator
A free CMU wall calculator: blocks, mortar bags, grout and rebar for any walls and openings, with bond beams and joint reinforcement. Runs in your browser.
-
Spare boards for culls now show up in the framing budget
The open-source wall framing takeoff budget now prices a typed lumber cull allowance as its own line per board size.
-
A free dormer framing calculator: every stud, rafter and valley from four numbers
Width, eave height and two roof pitches give a dormer's studs, rafters, valleys and the hole in the main roof. Free, in your browser, MIT licensed.
-
How many outlets and switch boxes does a house need? A free calculator that shows its sums
A free electrical rough-in calculator: type walls and doors, get receptacle boxes by the 6 ft wall-space rule, switch boxes, cable rolls and cost.
-
Fireblocking quantities: three ways a bad wall broke the counter
The wall framing takeoff fireblocking counter used to crash, return NaN or hang on a bad wall; it now refuses bad input with a reason and has a fuzz test.
-
A free fireblocking calculator: blocks and boards for tall wall cavities
A browser page that turns your walls and the cavity limit you type into block rows, bay-width blocks and boards to buy.
-
Fireblocking quantities for tall walls
The open-source wall framing takeoff now counts fireblocking rows, blocks and boards for walls taller than a cavity limit you type.
-
Counting the nails in floor blocking
The open-source floor framing takeoff now counts end nails for blocking pieces, at a per-end count you type.