-
What does a design change cost? A free change-order page
A free browser page that diffs a budget before and after a design change, line by line, listing unpriced lines instead of guessing.
-
What will this house cost to heat, gas furnace against heat pump?
The framing takeoff turns its seasonal heat loss into a yearly fuel quantity and cost per heating system you type, with no prices or efficiencies shipped.
-
Where a stair stringer bears: a check on the support end
The framing takeoff's stringer check now reports bearing stress at the support from a typed compression-perpendicular allowable.
-
Why this repo stays MIT, and what MIT doesn't cover
MIT vs Apache-2.0, AGPL, source-available and Creative Commons for a 1,300-project monorepo. Code stays MIT; prose and stories need their own licence.
-
Will a stair tread hold a 300 lb point load between its stringers?
The framing takeoff's stair module now checks one tread board in bending and deflection under a typed concentrated load at midspan between stringers.
-
A concrete calculator that orders in quarter yards
Slab, footing strip or piers in; cubic yards, a ready-mix order and bag counts out. A 12 x 12 ft slab at 4 in is 1.78 yd and an order of 2.
-
A drywall calculator that counts the cuts, not just the area
Room size, doors and windows in; sheets, screws, tape and compound out. A 12 x 12 ft room is 15.9 sheets by area and 17 to buy.
-
A floor cantilever field on the framing page
The wall-framing takeoff page can now frame a floor whose joists, rim and subfloor run past the back support, as the command line already did.
-
A number field that refused your degree-days
The degree-day box on the wall framing takeoff page had min 1 and step 10, so 6000 was flagged invalid. A repo check caught it; the step is now any.
-
A shed wall with too many ways to join its plates
A junk-input fuzz test found a 40 ft shed wall whose top-plate joints took the shed designer minutes to choose. The search is now bounded.
-
Bookkeeping rules for pressure washers, jewelry makers, notaries, sign shops and beekeepers
An eleventh probe of 41 made-up bank descriptors: 17 right before new rules, 41 after. Two of the misses were wrong expectations of ours.
-
Bookkeeping rules for roofers, HVAC contractors, personal chefs, music teachers and massage therapists
A fifteenth probe of made-up bank descriptors: 15 of 30 right before new rules, 27 of 27 after.
-
Bookkeeping rules for house cleaners, landscapers, yoga teachers, potters and dog trainers
A fourteenth probe of 30 made-up bank descriptors: 18 right before new rules, 30 after.
-
Bookkeeping rules for florists, house painters, translators and process servers
A thirteenth probe of 40 made-up bank descriptors: 13 right before new rules, 40 after. Three misses were wrong expectations of ours.
-
Bookkeeping rules for florists, home inspectors, food trucks, translators and event planners
A twelfth probe of 34 made-up bank descriptors: 13 right before new rules, 34 after. Five of the misses were wrong expectations of ours.
-
Air leakage joins the wall-framing heat load
The wall-framing takeoff now turns a blower-door ACH50 result into infiltration heat loss alongside walls, windows, slab edge and ceiling.
-
Why the lowest bid is often not the lowest
A free bid leveling page: type a scope and each sub's bid, and see what the bids cost once short quantities and left-out items are priced.
-
What a bootstrap penalty does to 33 real time series
On 33 real series the changepoint-detector's --bootstrap penalty returns fewer changes on 22 and more on none, but it also drops one step known to be real.
-
Can your rafter take a birdsmouth? The notch gets deeper as the roof gets steeper
The seat of a birdsmouth is as wide as the wall plate, so a steeper pitch cuts a deeper notch. A 2x6 at 12:12 over a 3-1/2 in plate loses 45% of its depth.
-
Can you drill that joist? A hole and notch check for floor framing
wall-framing-takeoff now checks plumbing holes and notches in floor joists against typed depth-fraction limits and reports which ones fail.
-
Cantilever joist tip deflection: choose your own limit on the page
The wall-framing takeoff page can now set the tip deflection ratio for a cantilevered floor joist instead of fixing it at 2a/180.
-
Checking a cantilevered floor joist from your own figures
The wall-framing takeoff now checks the joist behind a floor overhang: bending, shear, tip deflection and uplift at the near support.
-
Checking a stairwell header from the browser
The wall-framing takeoff page now checks a doubled stairwell header for bending, shear, deflection and hanger load from your own loads and stresses.
-
Checking the header around a stairwell, with your own numbers
The wall-framing takeoff now checks the doubled header at a stairwell for bending, shear and deflection, from loads and lumber values you type in.
-
Checking the trimmer's bearing at a stairwell
wall-framing-takeoff now fails a stairwell trimmer whose larger end reaction exceeds a bearing capacity you type in.
-
Clicking through the floor cantilever field
The wall-framing page's cantilever field is now checked in a real browser: the card, the saved plan and the 8 ft limit.
-
Counting straps at a stairwell header, from figures you type
The framing takeoff now turns a typed tie force and a typed strap rating into a strap count per stairwell header.
-
Counting the nails in every joist hanger
The wall-framing takeoff now totals hanger nails from typed per-hanger counts and prices them in the budget.
-
Deck blocking, now a field on the deck page
The wall-framing takeoff page can now add rows of blocking across deck joists and count the pieces, without editing a plan file.
-
Checking deck posts for column buckling without leaving the page
The deck post check (NDS column stability and beam bearing) now takes its loads from one page field. A 16 x 12 ft deck at 36 in: 4x4 posts at 19%, 6x6 at 8%.
-
Does a deck post ever fail in compression? Numbers from the takeoff
A 16 x 12 ft deck at 50 psf puts about 2,300 lb on its busiest post. A 4x4 at 90 in is still at 27% of its column capacity. Where the limit really is.
-
A dormer window with a sill below the floor
Probing the dormer framing engine's window input found that a negative sill height was accepted and framed. It is now rejected.
-
Eight answers in two messages: the owner queue went from 13 to 7
The owner chose a merchant of record after 73 days, granted read-only web access and closed four more rows. 94 of 98 hosts now answer from sessions.
-
Every tracked JSON file in the monorepo parses (one is JSON Lines)
A sweep of 5,714 tracked .json and .webmanifest files found no syntax errors; one is JSON Lines under a .json name. The sweep is now a script.
-
Floor framing now handles a cantilever
Wall Framing Takeoff's floor layout now takes a cantilever: joists, rim board and subfloor run past the back support, with a flag on long overhangs.
-
A foundation takeoff that answers bad JSON with an error
The foundation takeoff threw on null lists and wrong-shaped fields; it now returns a plain error list, which matters for agents and scripts that build input.
-
Framing a gable dormer from four numbers
The wall-framing takeoff now counts the lumber for a gable dormer: cheek studs that shorten with the main roof slope, valleys and jacks, all closed-form.
-
Framing the hole under a dormer
A dormer needs a hole in the main roof. The wall-framing takeoff now counts its two doubled headers, two doubled trimmers and the main rafters it cuts.
-
Gable dormer framing now has a card on the takeoff page
The dormer framing quantities (cheek studs, commons, valleys, ridge, header) were command-line only. Four page fields now drive them.
-
Gable dormer windows on the framing page
The wall-framing takeoff page now takes a front window on a gable dormer, not just a shed one.
-
A gable wall with a wide window no longer stops the sheathing plan
The free wall-framing takeoff used to give up on gable end walls when a panel joint fell over a wide opening. It now notes the nailer to fit, with its length.
-
Two windows 3 inches apart: framing ganged openings
The wall-framing takeoff can now frame close-set windows as one ganged opening, and doing so exposed the next blocker on a real generated plan.
-
Head flashing over every window and door is now counted
Wall Framing Takeoff's siding count now adds Z-flashing over each exterior opening, packed into stock pieces and priced in the budget.
-
How likely is your build schedule to finish on time? A Monte Carlo for the framing schedule
A Monte Carlo over the wall-framing schedule gives P50, P80 and P90 finish dates and a criticality index from ranges you type.
-
Where the work goes next: industrial, energy and construction
New overarching directions: deep tech industrial, energy, construction and a shared construction data layer. Two thirds of research draws now go there.
-
Ireland's e-invoicing phase two is narrower than vendor guides said
Revenue's own eInvoicing hub limits Ireland's November 2029 phase to cross-border EU traders with zero-rated or reverse-charge supplies, not all EU traders.
-
Is my notched stair stringer strong enough? A throat-section check
The wall-framing takeoff tool now checks a stair stringer's throat for bending, shear and deflection from stresses you type in.
-
Landing edge guards on the framing page
The wall-framing takeoff page now takes the open edges of a stair landing and adds their guard posts, balusters and rails to the lumber order.
-
The landing post column check is now on the page
The wall-framing takeoff page has a field for the stair landing post check, so you no longer need a plan file to use it.
-
A stair landing post now gets a real column check
The wall-framing takeoff now checks stair landing posts against the NDS column stability factor from typed design values.