-
The tennis feeder's CAD tests took 27 minutes because they rebuilt the robot 60 times
The tennis feeder's CAD check ran 19 of 20 CI minutes: an 18 s part build was requested ~60 times. A cache cut the suite from 1637 s to 323 s.
-
Wiring a launcher head that turns and tilts: the obvious cable route had 8 mm of slack and needed 13
Cabling a pan-tilt ball launcher: a twist run on the turntable axis, a 376 mm loop behind the pivot, and 20 AWG servo leads instead of 26.
-
A hard stop is only a stop if nothing hits first
Adding end stops to the tennis feeder's turntable showed the head would hit the hopper posts 4 degrees before reaching them. Two sets of posts moved out.
-
A home switch that says which side you're on
Drawing the tennis feeder's home switch showed the firmware took any closed switch as home: a head left 3 degrees past it aimed 1.3 m wide.
-
A tachometer that could only say 0 or 6,000: wiring the ball machine's brain to its motors
Writing the Pi drill runner for an open-source ball machine found a 6,000 rpm-step tachometer and a wheel loop that never settled.
-
The tennis-ball feeder's head wants to look up, and that makes the elevation drive easier
Measured from the CAD, the tennis feeder head's weight pulls its nose up at every angle, so one actuator pushes one way, 18 to 100 N.
-
A straight line in degrees is a curve in millimetres: firmware for the tennis feeder's elevation actuator
Spreading the tennis feeder's elevation angle evenly over its actuator's stroke aims up to 1.46 deg high: a 20 m/s drive lands a metre deep.
-
Ten seconds a ball: sizing the drive that meters the tennis feeder's balls
The feeder's listed linear actuator would need 9.7 s a ball. A servo crank needs 1.7 s, and the firmware was counting balls before they reached the wheels.
-
Turning the tennis feeder's head: a stepper, a printed gear and two collisions nobody had looked for
Sizing the ball feeder's turntable drive from the CAD's own inertia, then sweeping the turned head, found two clashes in the shipped design.
-
The ball feeder's hose take-up sent balls uphill, so it is now a sliding sleeve
A ball-carrying hose wrapped 180 degrees round a pulley climbs on one leg. The feeder now uses a sliding sleeve, which moved the hopper outlet up 300 mm.
-
The feeder's hose check never turned the head sideways
The tennis feeder's hose checks assumed the head pointed straight ahead. Turned 30 degrees at full tilt, the hose needed 31 mm more slide.
-
The take-up track gets its tie brackets in CAD
open-tennis-robots now models the two printed plates that tie the hose take-up track to the hopper frame, clash-free across the elevation sweep.
-
The tennis-ball feeder's take-up track: the ties are fine, the hose pull is the unknown
A statics check on the two brackets that tie the feeder's hose take-up track to its hopper frame, and what it says about what to measure first.
-
How square must a tennis-ball launcher's wheels be to its head plates?
In the open-tennis-robots feeder CAD, a 67 mm ball has 6.5 mm either side between the head plates, which allows 3.5 degrees of yaw.
-
How square must a ball-launcher wheel axle be? 0.75 degrees of stack against 3.5 allowed
A tolerance stack for the open tennis feeder head: assumed laser and spacer tolerances give 0.75 degrees worst case against a 3.5 degree limit.
-
How fast can the tennis-ball feeder's wheels throw with topspin?
The feeder model now finds the range of launch speeds its wheels and nip can deliver at a given topspin.
-
The tennis feeder's hose take-up is now a part, not a number
A 300 mm pulley on a 489 mm track now exists in the feeder's CAD package, checked for collisions with the braces and the swept launcher head.
-
The ball hose on our tennis robot has to move backwards as the head tilts
Sizing a floating-pulley take-up for the ball hose of an open-source tennis ball feeder, and a surprise: the pulley must reverse at level.
-
A ball feeder's wheels need to push 241 N, and the design assumed 60
Tying the tennis feeder CAD to its flight model: launch wheels near their rpm limit, and the nip must push four times what the retainer check assumed.