-
One badly fitted wheel out of 56 told our ball machine its motor controller had no lag
The tennis feeder's ESC-lag survey picked 0 on one build because one wheel fit 30 times worse than the rest. Trimming such wheels fixed every simulated case.
-
Forty microns of wear would have switched off our ball lift's jam detector
One stiff disc spring on our tennis ball lift's slip hub lost 61% of its torque after 40 microns of facing wear, and jams went undetected. Four discs fix it.
-
Five microseconds of sensor jitter would triple our tennis feeder's spin error
Our feeder reads spin from wheel-speed drops. Simulated, 5 us of tach jitter takes it from 1.6% to 5.3% off, so the board now flags fits it cannot vouch for.
-
One tennis-feeder wheel read 48% high because the Pi spoke too soon
A 1,107 rpm launcher wheel read 1.48x its true drop. The board's snapshot ended three revolutions after the ball. Holding the next speeds fixed it.
-
The tennis feeder already knew how its wheels would recover: it had sent the commands
The open tennis feeder now fits each ball's wheel-speed drop with the ESC commands it logged. On the simulator its spin error fell from 8% to under 2%.
-
The tennis feeder now refuses a calibration drill on the wrong ESC lag
The open tennis feeder's board reports its ESC lag setting, and the Pi stops a calibration drill when it disagrees with the last survey.
-
The tennis feeder corrects its own aim mid-drill
Every four shots the feeder now refits its launcher from the wheels' speed drops and re-plans the rest of the drill. Simulated misses fell from 5.2 m to 1.2 m.
-
The tennis feeder now finds its own ESC lag, and the edge-time fit that didn't help
The open tennis feeder's board now picks its ESC's lag from its own balls. On the simulator, spin errors of 13-18% fell under 1%. An edge-time fit did worse.
-
The tennis feeder notices an empty hopper from its own wheels
No ESP32 pin was left for a break-beam, so the tennis feeder now judges each feed stroke by how much its launcher wheels slow when a ball goes through.
-
Our tennis feeder misread spin by 20% behind a lagging ESC, until each build's own balls picked the lag
A second lag in the ESC left our feeder's spin reading 20-24% off. Picking that lag from a drill's own balls brings it to 3-6.5%; guessing it is worse.
-
The tennis feeder was cutting its slow wheels short
Retesting the feeder's 1,000 rpm floor found the Pi was freezing slow wheels' data too early. Holding 0.3 s fixed the readings; the floor stays.
-
The tennis feeder's empty-hopper check stops trusting the target speed
Fed as the speed gate opens, the target-based ball check misjudged 29 of 972 simulated strokes. Measuring the drop from the pre-ball speed misjudged none.
-
The tennis feeder's wheels double as a radar gun
Each ball takes its momentum from the launcher wheels, so their speed drop gives its exit speed. A shot log now calibrates the launcher with no radar gun.
-
The tennis feeder's worst-fitting wheel was looking in the wrong place
One wheel in 56 fitted 10 to 60 times worse than the rest. The cause: the fit anchored two revolutions after the ball. Walking it back fixed all 21 cases.
-
The tennis lift remembers its jams: a wear count that survives power-off
The open tennis feeder's firmware now counts every lift jam in flash and flags the slip hub for a bench re-set after 300, the figure its wear model allows.
-
The tennis lift's sense amplifier against its 20 kHz ripple: the averaged model holds
A switched 0.25 us simulation of the tennis lift's INA186 sense path: a few mA of ripple, no bias in the mean, 4 us of delay.
-
Watching a slow launcher wheel past the verdict: 500-750 rpm drops from 1.84x off to under 1%
A tennis feeder's slowest wheels had three or four revolutions before the shot's verdict. Watching them a little longer brought every ball's drop within 1%.
-
Why a slow tennis-launcher wheel never settled, and the gate that let balls go 13% off
A 510 rpm launcher wheel rang for ever because the tachometer's delay grows as the wheel slows. Scaled gains and a longer gate fixed it on the simulator.
-
Why the tennis feeder's spin reading was off by 8% when its speed reading was right
The open tennis feeder reads spin from wheel-speed drops. The 8% spin error came from leverage and a speed bias; faster spin shots halve it.
-
A current cutoff saves the tennis lift's motor, not its flight
A shunt and comparator let the tennis feeder cut a jammed ball lift in 30-90 ms. The simulation also showed what no cutoff stops: the rotor's inertia.
-
A ball-lift flight with a pad that lifts off the belt round each pulley
Why a welded cleat alone nearly doubles a ball lift's belt pull, and the printed cap with a loose pad that fixes it without stopping the belt wrapping.
-
A jaw coupling's free play rang the tennis lift's start. A 100 ms ramp fixed it
Modelled as a spring with play, the tennis lift's jaw coupling rang switched starts to 2.3x the assumed torque. A firmware soft start fixes it.
-
A slip hub takes the tennis lift's jam off the flight
A friction slip hub on the feeder's lift pulley cuts a jam's peak on a flight from up to 214 N to 51-88 N in simulation, and forced a lower current trip.
-
A test piece has to print the hole the part prints
The tennis feeder's bearing test ring now stands up so its bores print sideways like the boot's, with one bore in the press window per printer.
-
Print a test ring before you press a bearing into PETG
Printed holes come out small, so a press fit in PETG cannot be drawn blind. The tennis feeder now ships a seven-step bearing test ring.
-
Holding the tennis lift's speed steady quietly broke its jam detector
Scaling a DC motor's PWM duty to the battery fixed a belt resonance, but a low-side shunt then let a simulated jam go uncut. How we caught and fixed it.
-
Would a bigger pulley stop our ball lift's belt jumping a tooth? The model says it makes it worse
A jammed ball slackens one strand of our tennis ball lift's belt. Tooth strength has 7.7x to spare; ratcheting has 2.5x, and a 20-tooth pulley lowers it.
-
Stop Simulating Once the Answer Can't Change
A contactor check ran 16,590 RK4 steps to find a peak that lands by step 178. An energy bound now says when to stop, with bit-identical results.
-
The physics was fine; the function calls were the cost
Inlining three hand-written RK4 loops cut the open tennis robots test suite from 160 s to 96 s with bit-identical results.
-
Rerunning the tennis lift's jam sweep with the belt as 62 masses: the cutoff holds, a start goes slack
The tennis feeder's lift belt as 62 masses on springs in the jam sweep: every jam still cut by 89 ms, belt pull capped by the slip hub, slack on starts.
-
The tennis lift's belt is a spring too, and it rings where the coupling does
The tennis lift's belt stretch, modelled: it splits the 49 Hz drive mode, barely moves jam loads, eases starts, and slackens the down strand in hood jams.
-
The tennis lift's empty belt rings at the rate its flights pass, and no belt tension fixes that
A string model of the tennis feeder's lift belt: the empty belt rings inside the flight-passing band, and the pluck figure was 24% high.
-
The tennis lift's jam sensor stops reading the throttle
A low-side shunt reads duty times current, so the tennis lift's jam trip rose as the duty fell. A shunt inside the diode loop holds it at 1.77 A.
-
The tennis lift's pulley gets its own shaft, and the motor has to get shorter
The tennis feeder's lift pulley moves onto its own shaft in two bearings so the gearbox carries torque only; the collision check then caps the motor at 75 mm.
-
The tennis lift's slip hub goes back to 0.9 N m, and 0.8 is one step too far
Three full jam sweeps on the tennis feeder's lift: 0.9 N m cuts the flight's worst hit from 91 to 84 N, and 0.8 starts slipping on soft starts.
-
The tennis feeder that would have tripped its own battery
Sizing the open tennis feeder's fuses found a firmware fault: two launcher wheels starting from rest could ask about 98 A of a 30 A battery.
-
The 400 amp click when the tennis feeder switches on
Closing the tennis feeder's e-stop contactor onto empty ESC capacitors would peak near 394 A on assumed figures; a 4.7 ohm precharge cuts it to 20 A.
-
The tennis feeder's hose check scored every curve in full before rejecting it
The feeder hose search scored 115,000 candidate curves in full before testing any. Checking point by point made it 7.6x faster with identical floats.
-
The servo that would have undone the tennis feeder's precharge
A servo seeking home during the precharge would leave the tennis feeder's bus 16 V short, so the contactor would make ~223 A. Now it waits for a feed.
-
The tennis feeder's actuator lead needed its tie further up the body
Five wires to the elevation actuator: a tie 70 mm up its body gives one 220 mm cut that fits every pose; ties at 15 to 30 mm fit none.
-
The tennis feeder learns when its power is really on
An opto on the contactor coil lets the tennis feeder hold its stepper off through the precharge: 45 A down to 20 A on assumed figures.
-
The tennis feeder's position sensor was picking up its own motor
The pot wires share a 1.39 m lead with the motor pair. No capacitor: 8% of readings at the rail. 100 nF: 0.55 mm off. 1 uF: 0.055 mm.
-
The tennis feeder's brake guard was reading its own brake
Braking lifts the very battery reading that decides whether the ESCs may brake, so one threshold flipped every 10 ms. A 700 mV band from the model fixes it.
-
Two GPIO pins and a cable the clash check never saw
Routing a DIY tennis feeder's cables found a pin clash that would have stopped two motors, and a CAD fuse that hid a cable from the clash checks.
-
When the tennis feeder slows its wheels, the energy has to go somewhere
Braking ESCs push up to 170 W back onto the tennis feeder's bus; with the contactor open it passes 30 V in under 1 ms. A diode and a firmware rule fix it.
-
Two fixes for one slow CAD suite, found an hour apart, that stack: 27 minutes to under 4
A CAD suite near its 20-minute CI limit: caching a rebuilt model took it to 349 s, and running each clash sweep once, beside the other tests, to 219 s.
-
Lifting tennis balls 2.3 metres: why the lift's inlet came in from the side
A cleated-belt ball lift for an open tennis feeder: why the ball enters from the side, why the sump moved, and the numbers on paper.
-
The trough that couldn't reach the hopper
Drawing the catch net's ball trough for the open tennis feeder showed balls end up 2.2 m below the hopper. The design note said they would roll in.
-
Stirring a tub of tennis balls without jamming one
The open tennis feeder's tub drains through a 75 mm hole for 67 mm balls, so a few balls can bridge it. A little geometry chose where the agitator's arms go.
-
Tensioning a 2.4 m ball-lift belt: 7.5 mm of travel, and a tension you can count by hand
The top pulley tensioner for an open tennis-ball lift: where 7.5 mm of travel comes from, why 10.5 N, how to set it by counting swings, and a flight fix.