Clothing Design Studio · Pattern pieces · Size finder · Launch path

Sew the pattern onto a body and see where it pulls

A size chart compares two numbers: the garment's chest and yours. Cloth does more than that. It hangs from the shoulders, takes length going round the chest, and stretches where the body is bigger than the cut. This page takes the drafted front and back pattern pieces, sews them at the shoulders and side seams around a body built from your measurements, sets the sleeves into the armholes around the arms, lets gravity settle them, and colours each part of the cloth by how much it stretches around the body.

A simulation from typical drafting ratios, a smooth body made of ellipses, and fabric stiffness you type or guess. Body and sleeves on straight arms held out 45° or lowered against a side that gives an assumed amount; no hood or rib bands yet. It shows ease and tension; it is not a promise of fit. A sample garment on a real person always wins.

Garment

Body (cm)

Sleeves

Lowered: the garment is sewn with the arms out, then the arms swing down until they rest against the sides. A real side gives where the arm presses; "Side gives" is how far, for arm and side together. 3 cm is an assumption, not a measurement: at 0 this body's arms stop at about 28°, at 3 cm at about 18°.

Fabric

Stiffness is the pull, in newtons per metre of width, that would double a strip's length if the cloth stayed linear: the slope of a gentle strip-stretch test. The presets are rough guesses, not lab figures. Where the cloth is tight the stretch is set by the body and hardly depends on this number; the pressure is directly proportional to it.

On the body

not stretched1-3% stretchabout 6%12% or more

By level

WhereBody girthStretch round the bodyMost stretchedAverage gap to the bodyTouchingPressureReading

Sleeves

WhereArm girthStretch round the armMost stretchedAverage gap to the armTouchingPressureReading

Checks

How it works, and what was checked

The front and back pieces are meshed into triangles on a grid inside their stitch lines. Every grid edge is a spring set from the fabric's stiffness, solved with extended position-based dynamics (XPBD) in many small time steps; the springs on the outline carry half a cell, so the panel's stiffness per unit width is the number you enter. The panels start on a loose tube around the body and the sleeves on a tube around each arm; the shoulder, side and underarm seams are pulled shut and each sleeve cap is sewn into its armhole, joining points at the same fraction of each curve's length so the cap's ease is gathered in, all with gravity off; then gravity is switched on and the garment settles. The arms are straight, held 45° out from the sides (an A pose, as virtual fitting avatars use; with the arms nearer the sides the underarm has to wrap under the arm and pulls the shoulders), and round, tapering from your upper arm girth to your wrist, with a slightly fuller deltoid at the top that carries the shoulder out onto the arm. The body is a stack of elliptical sections whose girths are your chest, waist and hip, with height proportions from the same body model as the size finder's try-on.

Before any garment, the solver is checked against answers known in closed form (drape.test.mjs): a strip hanging under its own weight stretches by ρgL²/2K (within 2%), a nearly unstretchable strip between two pins sags like a catenary (within 3%), and a tube pulled over a cylinder takes the stretch the two girths dictate, with a contact force that approaches Laplace's law, pressure = tension ÷ radius, as the time step shrinks. The pressure shown here is that law applied to the simulated stretch.

Putting arms in found a drafting error (fixed 2026-11-13): the sleeve piece had been drawn with the flat, laid-down bicep as its full width, so at M it was 24 cm round, and the drape stretched it 37% round a 31 cm upper arm. Its length also ran from the underarm instead of the shoulder point, so sleeves were a cap height too long. The pattern now draws the whole sleeve (about 36 cm round, 18 cm flat, at M, with a 10 cm cap) measured from the shoulder point, as the spec sheet does. You can enter your own flat bicep above to see a narrower or wider sleeve.

Known limit: with the sleeves in, the neckline shows a few percent of stretch (about 7% on an M tee, against 1% for the body panels alone) and the tops of the sleeve caps bunch slightly. Real tees don't pull at the neck in this pose, so read colour at the neck as a limit of the model, not as a fault in the pattern. Tested on 13 November: it is not the bump of the deltoid (lowering it made the neck worse, 6.7% to 7.6%); with slipperier contact it doubles (12.1%) and with the arms raised to 60° it halves (3.8%), so it is the sleeves, held on the arms by friction, pulling the shoulders outward. Swinging the arms down after sewing reaches only about 28° on this smooth body (a real torso gives where the arm rests on it) and changes the body readings by under a centimetre, while the cloth pinched at the underarm reads as false stretch, so the page keeps the 45° pose by default.

Since 16 November the arms can be lowered against a soft side ("Arms: lowered to the side"). Below the shoulder the torso is carved away round the arm, leaving 1.2 cm for the two layers of cloth at the side, as a real side gives under a resting arm; "Side gives" caps how deep the carving may go below the armpit, which sets how low the arm comes (this body: 28.5° rigid, 22° at 2 cm, 18° at 3 cm, 15° at 4 cm). The pressed flesh is not bulged out at front and back. At 3 cm the arms come down to 18°; all nine drapes tried (tee, long sleeve and hoodie in S, M and L) settle with no cloth inside the body, against two unsettled and sixteen points inside on the rigid body, and on an M tee the worst-stretched sleeve triangle at the underarm falls from 138% to 98%. The cloth pinched between arm and side still reads as a bicep peak, so trust the bicep mean in this pose. The give itself is a guess: no one has pressed an arm into a real side and measured it for this page.

One thing the flat numbers miss: on the default body every drafted tee, sweatshirt and hoodie that is not stretched ends about 5.5 to 8 cm higher than its body length measured straight down from the shoulder, because that length goes over the shoulder and round the chest and back. It is a model result, not yet checked against a real garment on a real person.